Mark Crawford


Blog

How To Make A Tapering Jig In An Hour? – A Detailed Instruction

Posted by Mark Crawford on

The Tapering Jig is a sled with a table saw to create rip cuts on an angle. This item enables users to consistently adjust the reductions and cut to any hook up to 15 degrees. 

Additionally, it is a useful and easy-to-build tool. So if you want to know how to make a Tapering Jig in an hour, carry on reading this article as we will show you the necessary steps. 

How To Make A Tapering Jig In An Hour – 7 Easy Steps 

Step 1: Cut out 2 Pieces of Wood

The first thing you have to do before cutting is to measure two pieces of wood. The length of the wood is usually 30 inches, and the width is about 3 inches. 

You can freely adjust the two pieces’ size, yet those two have to be the same length. After finishing the measurements, you cut it with a Portable Table Saw and begin working on these wood pieces.

You can use a table saw or a hybrid one. If you are interested in the hybrid table saw, you can consult https://www.discoveriesla.com/best-hybrid-table-saws to find a product that suits you best.

Step 2: Connect the two pieces with a hinge.

Put one piece onto another and use a hinge to join them together. The hinge should be attached at one end of the jig. It also has to be at the center and parallel with the boards. 

Step 3: Drill holes

On the opposite end, you drill a hole on each piece’s top side, like the image below. The holes have to be deep and be an inch up high on each board. Plus, they should be big enough for the 1/4-inch diameter bolts to go through snugly.​ 

Step 4: Insert the bolts. 

You put the bolts into the holes and use a hammer to tap them until they are firm in place.

Step 5: Build the Spreader Bracket

To build the Spreader Bracket, you cut out a wood piece with 8-inches length and 2-inch width. Then, you round the edges and draw a middle line at 1 inch away from each side.

Next, you drill three 1/4-inch diameter holes: two holes of 1/2 inch at each edge on the centerline, and the third hole at 1 inch in from one edge on the centerline.

After that, you use a jigsaw and cut along the middle line to create a slot in the spreader bracket. However, you have to leave a hole on the right side for the bolt.

Step 6: Attach a Lip

After cutting a 2-inch wide piece of wood, you join this piece to the left side of the jig with some deck screws. It should be 1 inch away from the top of the board. 

Step 7: Attach the Bracket to the board

To finish this Tapering Jig, you attach the bracket to the board. 

Place the hole on the right bolt and the slot over the left bolt. Tap it down into its place. After you add a flat washer, you lock the bolt onto the right bolt. Then, you tighten till it is snug, yet not too tight to rotate on the bolt.

In short 

We hope this article about “how to make a Tapering Jig in an hour” will help you successfully create one for yourself. These steps are very easy to follow, so you don’t have to worry too much. Anyway, good luck with your work, and thank you for reading! 

Blog

What Table Saw Blade Is Best For Ripping –  All You Need To Know

Posted by Mark Crawford on

Each table saw blade comes to the market at different sizes, prices, and functions. If you are struggling with choosing what table saw blade is best for ripping, https://www.discoveriesla.com will help you out. Do not hesitate to give our article a check!

What Table Saw Blade Is Best For Ripping?

It’s a good table saw under 300$ for ripping; and to To choose one, you need to consider:

Tooth Geometry

Tooth Geometry plays an essential role in ripping certain materials such as MDF and laminates. A tooth geometry includes the top profile, the angles, and the hook angle. 

The angles and top profile have to work together. This combination will produce a cleaner cut. The hook refers to the angle of the tooth face about the central line of the blade. With the positive hook of the blade, the teeth will cut more aggressively. By contrast, the negative hook means that the teeth are angled back instead of blade rotation control.

Tooth Count 

The number of teeth is one of the most important things when choosing saw blades that are best for ripping. 

Generally, a blade with more teeth can make smoother cuts but runs hotter. To abstain from overheating, 3-5 teeth need to be locked during a rip cut. 

A blade with fewer teeth for cutting thick stock would be perfect to keep up the right engaged-tooth proportion. The number of teeth will depend on your purpose, but people normally choose between 40 and 80.

Kerf Width

A saw blade’s teeth need to ensure a wide enough cut to permit the blade plate to go through the kerf. To make the blade work smoothly and provide perfect cuts without a ton of scoring on the cut’s edge, you need to ensure the blade plate is considerable enough to absorb vibration and deal with the heat generated during the cut.

Blade Coatings

Blade coatings can help blades run cooler and make them simpler to clean

Conclusion

Overall, there are many tables that saw blades options for you to choose from. Therefore, you need to consider carefully which tool best suits your purposes and job requirements. With the guide of what table saw blade is best for ripping, you can quickly determine to buy one that suits you the best.

Good luck with your purchase, and see you in our next posts on how to know whether it’s a good table saw under 300$!

Blog

Essential Knives You Will Need For All Your Cooking Tasks

Posted by Mark Crawford on

cooking is fun with great knives

Cooking is an enjoyable activity that most people love. But in order to complete some very specialized cooking tasks, you will often need to bring in specialized knives. But how many knives would you need in total?

The truth is, there are a lot of knives out there for you to choose from. However, you will only need the following ones for a satisfying experience.

The first knife, and arguably the most important one, is a chef knife. The chef knife might be a Western-styled one or a Japanese one. It’s designed to do most of the tasks in your kitchen with ease. A good chef knife can help you slice, dice, mince, devein, etc. your foods. So, it’s a must-have.

The next one on the list is the paring knife. This type of knife is not that necessary all the time. But with it, you can do more tasks that require precision. This type of cutlery is not that expensive either. You can easily equip yourself with one for less than $30.

And for those of you who love slicing bread, a serrated bread slicing knife is a must. With this type of knife, you will find it a lot easier to cut your loaves of bread without breaking it. This type of knife is designed with serration so that it can slice through all kinds of bread easily.

Finally, if you’re in love with beef steak dishes, then a good set of steak knives will be a no-brainer. You will find eating beef steak a lot more enjoyable with this kind of knife. They’re serrated knives just like the bread slicers above. But they’re often a lot shorter and come in a set.

Blog

3 Reasons Why You Should Choose Japanese Knives For Your Kitchen

Posted by Mark Crawford on

why japanese knives

When it comes to cooking cutlery, you have a wide range of choices for knives from brands all around the world.

But, there are a lot of people who opt to buy Japanese knives for specific reasons.

And in this post, I will share with you about those very reasons.

The first reason is that Japanese knives, especially chef knives, are very well made and of very high quality.

They’re often made with high-quality stainless steel and G-10 handle.

These knife sets from Japan also come with a full set of knives that you will need for all of your cooking tasks such as slicing meat, chopping veggies, carving out your beef steaks, etc.

Another solid reason to choose Japanese knives is that you will often find specialized knives that the Western world won’t be very familiar with.

Let’s take the sushi knife for example.

You won’t find many choices from brands from Western culinary.

But you can find plenty of them from Japanese brands.

So, it’d be a wise choice to stick to Japanese brands when it comes to their traditional dishes such as sashimi and sushi.

And finally, these knives are very budget-friendly as well.

I’m not talking about knives or knife sets that can easily set you back a few hundred bucks.

I’m talking about more budget choices like below $50 or even below $30.

For this price range, you can’t find any other better choices than the ones coming from Japanese knife brands.

Of course, there are still great brands like Shun that offer premium knives.

But it’s your choice to choose them or not.

Blog

Top 10 Destinations You Can’t Ignore When Visiting Latin America

Posted by Mark Crawford on

Galapagos Islands

There are not many spots to equal the untamed life of the Galapagos Islands. Snorkel with fun loving ocean lions, watch the entertaining mating move of the Blue-footed Booby and see wild Monster Turtles in the Good countries. All from the solace of an extravagance yacht, the Galapagos works incredibly well for couples and families the same.

Chichen Itza Mayan Remnants, Mexico

Be Indiana Jones for the afternoon and investigate Chichen Itza, one of the new Seven Miracles of the World. This old Mayan capital is the most celebrated in Mexico with sanctuaries, for example, the overwhelming El Castillo are adjusted to galactic occasions, for example, the spring and pre-winter equinox which offer the opportunity to see the staggering shadow snake of El Castillo.

Iguazu Falls, Argentina and Brazil

Taller and more extensive than Niagara, the loud Iguazu Falls is one of the most tremendous sights in South America. The 275 individual cascades spread over approximately 2 miles must be seen from the Argentine and Brazilian sides for differentiating vistas and by pontoon from the uneven waters underneath.

Torres del Paine Public Park

The Torres del Paine Public Park in Chilean Patagonia is a lovely region of snow-topped stone pinnacles, ice sheets and natural life effortlessly investigated from our preferred extravagance lodges. For the more audacious, a-list journeying and pony riding over the pampas are not to be missed.

Salar de Uyuni, Bolivia

Bridging the huge shining Uyuni salt pads is a stunning encounter. A scene of splendid white stands out wonderfully from the dark blue sky above. The Salar, close by volcanoes, desert and multi-shaded tidal ponds abounding with flamingos make this district a definitive outside of what might be expected objective.

Pantanal, Brazil

The Pantanal is the biggest wetlands territory on the planet and the top natural life objective in Latin America, the prairies, swamps, backwoods, lakes and streams are home to an inconceivable exhibit of species. Spot many fowl species, reptiles and interesting warm blooded animals, for example, Goliath Insect eating animals, Monster Otters and ungulate, not overlooking the subtle panther.

Havana, Cuba

Havana must be one of the most suggestive of urban areas, still capital of one of the final socialist systems. It overflows character, it has the disintegrating pioneer engineering, splendidly shaded exemplary American vehicles and old women puffing ceaselessly on natively constructed stogies. Nothing beats their enthusiastic bars to taste super cold mojitos and endeavor a couple of salsa moves. It has such a great amount to offer over a long end of the week or as a feature of broad Cuba trip.

Amazon Rainforest

The world’s biggest rainforest, the Amazon covers an enormous zone of Brazil also Peru and Ecuador among others. Take an extravagance voyage up little-investigated feeders of the strong Amazon Waterway or remain at an extravagance cabin to investigate with a specialist nearby Indian guide, fish for piranhas and recognize the numerous fowls, monkeys and cayman crocodiles.

Machu Picchu, Peru

Roosted on a wilderness shrouded mountain in the core of the Andes, investigating the sanctuaries and castles of this grand Incan bastion is an exceptional encounter. Regardless of whether came to by journeying the Inca Trail or going by extravagance train the vestiges are a spectacular site, particularly at dawn when most guests are still snoozing!

Rio de Janeiro

One of the incredible urban communities of the world, Rio de Janeiro has everything – dynamic nightlife, notable sights, sea shores, rainforest and Jamboree obviously! Head up to the pinnacles of Sugarloaf Mountain and Corcovado’s Christ the Savior for sublime perspectives on Guanabara Narrows and obviously the renowned sea shores of Ipanema and Copacabana beneath.

Blog

Visiting South America? These 10 Dishes Are Must-Taste Ones Then

Posted by Mark Crawford on

Making a visit to South America? Prepare to enjoy these nearby rarities.

South America presents voyagers with life-changing culinary encounters. Regardless of whether you favor plunk down suppers or in a hurry treats from road sellers, it’s almost guaranteed that regardless of which nation you visit, you’ll discover something to charm your taste buds. These 10 dishes are probably the most famous—and tasty—ones to attempt all through the landmass. It is safe to say that you are prepared to gather your sacks yet?

Related: Top Dishes in Latin American Cuisine

1. Ceviche (Peru)

This mainstream fish dish got its beginning in Peru however has gotten broad all through the seaside locales of both South and Focal America. New, crude fish (typically a white fish) is relieved in citrus juice (lemon, lime, or Seville orange), spiked with some warmth from bean stew peppers, and embellished with onion and cilantro. On the off chance that you love sashimi, you’ll flip for this delicacy.

2. Arepas (Venezuela)

This flatbread sandwich produced using ground maize batter or cooked flour can be loaded up with pretty much anything, from cheddar to meat to eggs. Contingent upon where you go, the quantity of arepa assortments on a solitary menu can go into the twofold digits! The heartier choices are now and then eaten as a principle course, while littler or less unpredictable arepas make for immaculate tidbits.

3. Empanadas (Argentina)

This fresh, half-moon formed cake has a hot, appetizing filling of cheddar, meat, or vegetables. In Argentina, each territory has its own particular flavor. One is a tidbit, yet a few can make a feast.

4. Pisco Sharp (Chile, Peru)

The Pisco Sharp is a famous mixed drink all through South America, however it’s the public beverage of both Chile and Peru. It is made with pisco, a cognac created in both Chile and Peru, blended in with egg whites, Angostura sharp flavoring, lime juice, basic syrup, and ice. Minor departure from the Pisco Harsh fuse diverse organic product squeezes that switch up the flavor. Many trust it’s the ideal backup to ceviche, so make certain to attempt both when in Peru!

5. Yerba Maté (Argentina)

This tea produced using the leaves of the South American rainforest holly tree is madly well known in Argentina, where you’ll see pretty much everybody hefting around their own metal cup and straw loaded up with this animating, stimulated mix. Maté is an obtained taste, however the beverage is addictively delicious once you become accustomed to it.

6. Pastel (Brazil)

More slender than an empanada, the pastel is another fresh baked good loaded down with an arrangement of fixings. Famous fillings of these delectable singed pies included dissolved cheddar, ground meat, hearts of palm, and little shrimp. In spite of the fact that pastel is normally an exquisite treat, it’s conceivable to discover sweet assortments loaded up with things like guava jam or chocolate.

7. Dulce de Leche (Colombia, Venezuela, Argentina, Uruguay, Brazil)

The deliciously sweet dulce de leche is a well known sugary treat that is fused into numerous South American pastries. The smooth caramel is made by stewing milk, sugar, and at times with vanilla, and presented including doughnuts and biscuits to toast. It tends to be elusive outside of South America, and numerous guests who attempt it just because are right away snared. Make certain to carry some home to fulfill those post-get-away yearnings! (Simply pack it safely in your portable suitcase, obviously.)

8. Brigadeiros (Brazil)

The brigadeiro is a chocolate truffle or bonbon local to Brazil. These magnificent pieces are produced using consolidated milk, powdered chocolate, and margarine, and secured with chocolate sprinkles—a chocoholic’s fantasy!

9. Platanos Fritos (All of South America)

Seared plantains, or platanos fritos, are a quintessential South American enjoyment. The delicate surface pretty much melts in your mouth, and the brittle consumed pieces are past scrumptious. These scrumptious treats can be discovered pretty effectively all through South America.

10. Chorizo (Argentina)

Argentina is a country of shameless carnivores, yet chorizo stands apart as one of the nation’s most delectable meats. You can discover this hotdog on the menu at pretty much any Argentine eatery, just as enticing you with its incomparable smoky aroma at each road slow down. Chorizo has advanced far and wide now, however don’t pass up on the opportunity to attempt it in its local land.

Make sure to proclaim any food you pack to bring across nation lines, and check with customs to ensure you can bring your preferred treats back—particularly natural products, veggies, and meat.